DIY Pipe Fitting Wooden Coat Rack Tutorial

This little seating area is great for putting on shoes and a quiet pet resting place and I love the vintage mould (I think that’s what the chalkboard is hanging on) but you know what? I was ready for a change. Surprise, surprise! haha!

eclectic-hallway

Time to get creative and since we love pipe and wood projects for a bit of a rustic industrial style (see this), those are the materials I used to create a pipe fitting wooden coat rack. 

What I used:

DIY pipe coat hooks

  • Three 3/8 inch galvanized flanges
  • Three 3/8 inch 90 degree elbows
  • Three 3/8 inch black caps
  • Three 3/8 inch x close steel pipe nipples
  • Twelve 3/4 inch sheet metal screws (these fit nicely for securing the flanges to wood)
  • RustOleum Universal Metallic spray paint + primer (oil rubbed bronze)
  • Scrap 1 x 6 pine board 
  • RustOleum Ultimate wood stain (Kona)
  • RustOleum Ultimate polyurethane
  • 2 drywall anchors and screws (to secure to wall)

What I did:

1. I connected my pipe fittings in this order: flange, nipple, elbow, nipple, cap.

DIY pipe coat hooks @diyshowoff

2. Then I gave them a few light coats of spray paint and let dry. 

DIY pipe coat hooks @diyshowoff

3. I cut my scrap pine board to 30 inches.

DIY pipe coat hooks @diyshowoff

4. Then sanded the edges smooth and wiped clean. 

DIY pipe coat hooks @diyshowoff

5. Next using a foam paint brush, I applied the wood stain and let it sit for a couple of minutes. You’ll want to wear gloves!

DIY pipe coat hooks @diyshowoff

6. Then wiped away the stain with an old rag and let it dry.

DIY pipe coat hooks @diyshowoff

7. After about an hour, I brushed on the polyurethane and let it dry according to manufacturer’s instructions. 

DIY pipe coat hooks @diyshowoff

8. Once everything was dry, I secured the first pipe hook to the center of my wood plank. Then secured the other two. 

DIY pipe coat hooks @diyshowoff

9. I attached it to the wall using drywall anchors and screws. 

DIY pipe coat hooks @diyshowoff

Perfect for hanging jackets, the dog’s leash, or my tote bag. 

rustic industrial pipe fitting coat rack @diyshowoff.com

Check back next week to see the tutorial for the dog silhouette wood plank wall art tutorial.

DIY Project Parade ~ DIY Pipe Curtain Rod Tutorial

HAPPY NEW YEAR, DIY SHOW OFF FRIENDS! 2011 was awesome and wishing you an even better 2012. Welcome to the First DIY Project Parade of 2012!

12 foot curtain rods are expensive!  I love the look of our new affordable DIY curtain rod made from pipe and fittings:

I knew True Value would stock the materials I needed:
2 – 6′ galvanized steel pipes (True Value will cut/thread the ends to any size)
3 galvanized 1/2″ flanges
3 galvanized 1/2″ tee fittings
3 1/2″ connectors {nipples}

Parts:

Drywall screws

2 finials and 1 wine cork

Tools:
Stud finder
Drill
Screw driver
Level

I gave all of my pieces a coat of Krylon‘s hammered metal:

1.  Find and mark studs. Measure/mark the height you’d like the curtain rod to hang (not my hairy arm!).

2. Attach “tee” to flange using nipple. Do this for all three pieces.

3. and 4.  Slide on curtain rings onto pipe at this stage. Tip:  Keep curtain rings clipped to plastic casing they came with or clipped to index card or piece of cardboard to help keep them in place during installation (not shown). Attach two flange sets to the ends of a pipe.

5.  Hold pipe with flanges on each end up to the wall, mark holes for screws (use a level to make sure rod hangs straight) by starting a hole with a spade bit or nail (hammer lightly).

6.  Four screws to each flange.

7.  Attach last flange set to remaining pipe.

8.  Slide on more curtain rings (I use 7 for each curtain panel).

9. Screw one end of pipe into the tee that’s secured to the wall.

10.  Twist flange so it’s flush to the wall.

Note:  The installation process will scuff your walls…you’ll need to touch up.

11. Repeat steps 5 and 6 for the other end.

12. Choose 2 finials that fit in your space and match your style. I spray painted mine to match the pipes.

13. Cut a piece of a wine cork in half.

14. Shave down the sides. (Make 2 pieces, one for each end of the pipe.)

15.  Push a piece of the cork into the end of the pipe.

16.  Screw the finial into place into the cork.

Done and ready for curtains!

I love the industrial look. {No Sew Drop Cloth Script Curtain Tutorial here}

More photos of the sitting room “Christmas un-decorated” coming up!  🙂

Let’s see what you’ve been up to!

The DIY Show Off

1. You must use the button above (ADD BUTTON HTML CODE FROM SIDE BAR TO YOUR POST) and link to this post to share the linky love. You post must be recent, shared at one DIY Project Parade only (not continuously) and be DIY related.
2.Include your name or blog name and project title. Add your permalink (not your blog url, but your DIY project post url). Feel free to link a Past Post, just invite your readers in a current post with a quick note.
3.Or email your link to thediyshowoff@gmail.com and I will add it for you.
4.If you notice your link has disappeared -please add the link back to The DIY Show Off to your post today, a button or a quick note to your readers about the party and try again! I love when everyone participates and readers check out everyone’s links, but I think the return favor of linking back is the nice thing to do so everyone plays fair and enjoys all of the projects and links. Also – this blog party is for DIY projects only. Links not related to DIY will be deleted. Please share your link one week only.

5.  If reading this in an email, pop over to http://diyshowoff.com to see the inspiring DIY projects linked up!
6.  NOW you can “like” the links!  What a fun idea!  Most liked links may be included in a post of DIY Project Parade highlights later in the week.

7.  Visit a few other links to make some new friends, get some creative ideas and feel free to leave me a comment. I’m likely sitting here on the computer and could use a happy distraction!
Don’t forget to come back Sunday evening and link up your 2011 DIY recap and my DIY year in review.
*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~
I was one of the bloggers selected by True Value to work on the DIY Squad. I have been compensated for my time commitment to the program as well as my writing about my experience. I have also been compensated for the materials needed for my DIY project. However, my opinions are entirely my own and I have not been paid to publish positive comments. FOLLOW TRUE VALUE ON FACEBOOK AND TWITTER!~*~*~*~*~

Pin It