Painted Upholstered Chair Tutorial {before and after}

Painted upholstered chairs – story of an unplanned DIY.

Does your DIY ever go like this: I started my day with big plans to finally sew the curtains in the family room. In order to do so, I needed to clean off the dining room table which was piled with boxes filled with ornaments and holiday decor and other junk from the shuffling around, rearranging and decorating {because of course the table in my craft room is piled high with an unorganized cluttered mess that also needs cleaned}.

DIY painted upholstered chair tutorial

Of course clearing the dining room table meant decorating for Christmas which lead me to the room right off the dining room that we’re currently calling the “sitting room”. So, in order to sew curtains for the family room, I had to clean the dining room which meant decorating the sitting room and in there were these chairs.

These $6 thrift store chairs. I loved the color and pattern. But I have had a difficult time with orange, fuchsia and olive green colors. Love them. But they don’t work in our home. I gave them a chance, but not even in our eclectic home. I considered slipcovers but I am decorating this room right now. No materials or time for slipcovers.

{before}

chair before

And I had the brilliant idea to paint them. Right then. That minute.

I had seen the upholstery painting tutorial at Hyphen Interiors in 2011. Loved it. Left an impression. Very inspiring.

I also knew I had most materials on hand. Paint! Everything except the fabric medium. I’ve looked at the bottles for sale at Michael’s in the past {for painted curtains} and knew they weren’t cheap. I was also still in my pajamas and on a mission. Sewing curtains, remember?! But these multi-colored chairs were an obstacle.

DIY girls thoughts: No fabric medium. No budget. No desire to run to the store. Lots of leftover latex paint. The only one who really sits in these chairs is the cat. So for now…if painting doesn’t go right, I can still slip cover them at a later date. GO FOR IT!

I found a left over can of Ralph Lauren paint that I hated working with as it was super watery. Perfect! I watered it down even further with water. I didn’t measure, just created a consistency that was still able to hold to the paint brush but watery enough to be absorbed into the textured fabric of the chairs. I used a 2.5 inchPurdy brush.

I gave the chairs a good cleaning, getting up all of the cat hair (FrogTape works great as a cat fur remover).

And I just started painting. My mixture of latex and water had amazing coverage.

I also taped off the legs using FrogTape.

painting upholstered chair

Sometimes I had to swirl the brush for coverage, then followed up with a straight brush stroke.

painting upholstery

And worked my way along the bottom edges, up the side, around the back, in the creases of the attached cushions and finished by painting the seat back and cushion.

painting an upholstered chair

I took a few breaks and a bigger one between the painting the two chairs. The Paintbrush Cover was perfect for keeping my paintbrush from drying out. It creates an airtight seal during usage. Simply place the brush in the cover and close the lid. After my break, I simply opened the cover, removed my brush. It was like I never stopped painting! {Thanks to Salvatore of the Paintbrush Cover for the gift…definitely something that’s going to get a lot of use around here. If you paint a lot…visit the link above to purchase a few for yourself. Definitely useful and convenient! 2 must have DIY paint tools to have on hand: FrogTape and the Paintbrush Cover.}

The Paintbrush Cover

One coat. It dried fairly fast. I removed the FrogTape which perfectly protected the wooden legs. Who even noticed those pretty legs with that crazy printed fabric before? Discovery: She has legs with beautiful carved detail!

removing FrogTape

The texture which was lost in the busy pattern…

before

upholstery before

now shows the quilted pattern with a solid color…

after

painted upholstery after

SO PRETTY!

And before you ask, yes…without the fabric medium, my chairs are rough. They have a vinyl look and feel. Since the paint is watered down…it’s not going to crack or chip or anything. The paint is absorbed into the fabric. I would recommend NOT skipping the fabric medium and to use the recipe shared by Hyphen Interiors. However…if you find yourself in a DIY emergency like me and aren’t particular about a sort of vinyl look/feel. And you have to do something or your entire Christmas decorating is going to be a big fail and you’ll never move on to the project that you planned to complete in the first place…I must tell you, I love these chairs now. Forget the slipcovers.

I knew I wanted to do more than just have a set of solid light grey chairs. My inspiration:

Serena & Lily Bark Miramar Racing Stripe Chair

Serena and Lily Bark Miramar Racing Stripe Chair

Of course I know that my chairs aren’t the same shape. They’re slender girls with long legs. But that stripe. I love that stripe. Not quite a knock off or copy cat project, but it’s what inspired my next steps…

I found the center of the chair and using FrogTape, created a stripe down the middle. I was sure to burnish the edges where the tape would meet paint. And using  leftover {watered down} brown latex paint, I painted in my stripes from bottom of the front of the chair, over the cushion, up seat back and down the back of the chair.

FrogTape stripe

I removed the FrogTape while the paint was still wet, pulling away from the wet paint. I did take a wet paper towel to carefully wipe away wet paint where a tiny bit seeped under the tape due to the texture of the fabric. See – it’s a good thing I have that vinyl-ish finish!

Removing FrogTape Stripe

Amazing transformation, right? Love it!

striped painted upholstery

Now I’m happy with my $6 chairs.And I was able to decorate the sitting room for Christmas.

See more Painted Upholstery Chair pictures in the sitting room mini makeover. 

painted upholstered chair tutorial

His & Hers painted pillow covers

painted pillow cover

{tutorial}

His and Hers Pillow Covers tutorial

I was able to get the dining room table cleared off and decorated and the clutter put away. (okay…for real, some of that was shifted to the craft room table which is dangerously close to an avalanche. Shhhh!)

I still haven’t sewn 6 of the 8 family room curtain panels. {Remember the no sew ruffled ombre tree skirt and the sewing machine being at the repair shop? One of these days I’ll get those curtains done. You don’t remember that I’ve had the fabric since June, do you?}

Perhaps another day, I’ll have a DIY plan that will go according to plan.

Joining the party here:

TDC Before and After

shabby creek cottage Beneath My Heart

 

Don’t miss a thing!
Facebook
DIY Show Off - FacebookDIY Show Off - TwitterDIY Show Off - PinterestDIY Show Off - FeedDIY Show Off - HomeTalkDIY Show Off - G+

*This is a sponsored post brought to you by FrogTape. The opinions are completely my own based on my experience. Results may vary. 

FrogTape Blog Squad

DIY Lighted Starburst Mirror Christmas Tree Topper {tutorial}

DIY Lighted Starburst Mirror Christmas Tree Topper

One thing I’ve never created but have always loved is a DIY starburst mirror. There are so many great tutorials, so many beautiful creations. The new white Christmas tree in the family room needed a topper. I have a white star (which you’ll see that I also used…there’s no such thing as too much bling at Christmas!). Here’s how I made the lighted starburst tree topper:

DIY lighted sunburst mirror Christmas tree topper

Materials:

  • about 30 BBQ skewers
  • about 30 plastic garden stakes
  • 7″ flat round mirror
  • 7″ cardboard circle (I traced my mirror onto a piece of white cardboard and cut it out)
  • FrogTape Delicate Surface
  • string of lights (mine is a string of 20)
  • spray paint (I used Rustoleum‘s Satin Lagoon)
  • 1 pipe cleaner
  • hot glue

Tutorial:

1. Using the FrogTape Delicate Surface, tape off the front of the mirror.

FrogTape Delicate Surface

2. Trace the mirror onto a piece of cardboard and cut out circle. Set aside.

DIY lighted starburst mirror tree topper

3. Flip mirror over. I used a Sharpie and traced the bottom of my FrogTape container, making a circle centered on the back of the mirror. I traced the lid of my spray paint can for a smaller inner circle.

DIY lighted starburst mirror tree topper

4. Lay out garden stakes round the outer circle to see if you’ll need to leave a small gap between each garden stake. Mine fit snug, just touching each other. I glued them into place on the outer circle.

DIY lighted starburst mirror tree topper

5. Next I glued a BBQ skewer, starting on the inner circle, spacing them between each garden stake.

DIY lighted starburst mirror tree topper

6. Mark the center of the cardboard circle. About 1/2″ from the center to the left and to the right, I poked a small hole using a pair of scissors.

DIY lighted starburst mirror tree topper

7. Thread through the pipe cleaner. Glue pipe cleaner into place on the back side but do not glue to the back of the mirror yet. The front side will be what attaches the starburst mirror to the top of the tree. I folded my pipe cleaner and covered each with a piece of FrogTape. {I realized after the fact, do not thread the pipe cleaner until after spray painting the cardboard.}

DIY lighted sunburst mirror Christmas tree topper

8. Spray the back of the mirror. Let dry. Flip and spray the front of the starburst mirror. I also gave my cardboard a light coat of spray paint. Let dry.

DIY lighted sunburst mirror Christmas tree topper

9. Glue base of lights (and some of the coated wiring if needed) into place. I tried to place the lights between skewers and garden stakes. The actual bulb sits above the mirror when looking from the front. My string of lights was enough to wrap around at few times. Be sure to leave the cord hanging for plugging in.

DIY lighted sunburst mirror Christmas tree topper

10. Once the lights are all glued into place, glue the cardboard backing into place over the lights/back of the mirror, back of the garden stakes and skewers. {I did not do this…as shown, my cardboard was glued to the back of the mirror before the lights.} Be sure the pipe clear is facing the correct direction to wrap around the top branch of the tree.

11. Remove FrogTape from front of mirror. All done!

DIY lighted sunburst mirror Christmas tree topper

It’s a pretty topper by itself, but I really like the reflection of the white star we already had on hand…

DIY lighted sunburst mirror tree topper

Reminder:  starting Monday, 12/10…

Christmas Tree Party

Keep up-to-date and get sneak peeks by following along:

Facebook
DIY Show Off - FacebookDIY Show Off - TwitterDIY Show Off - Pinterest
DIY Show Off - FeedDIY Show Off - HomeTalkDIY Show Off - G+

Instagram

Sharing here:DIY Show Off DIY Holiday Highlights

This is a sponsored post brought to you by FrogTape. The opinions are completely my own based on my experience. Results may vary.

FrogTape Blog Squad

How to Make a NO SEW Ombre Ruffled Tree Skirt

{no sew} Ruffled Ombre Tree Skirt Tutorial

With an eclectic family room makeover in progress, we’re decorating the Christmas tree with fun non-traditional colors for Christmas. I know – my house is a mish mash of themes but I do what I love and I’m loving walking from room to room with a different scene. However, finding a colorful non-traditional tree skirt is nearly impossible. Then I remembered that few years ago, I stumbled across a no-sew ruffled tree skirt and although I don’t remember where I saw it, I remember it was a lot easier than I imagined.

No Sew Ruffled Ombre Tree Skirt tutorial

It’s much harder to explain how to do it in words than actually working on this. It’s so easy! This could even be done using a sewing machine (which was my plan but I had to go to Plan B when my sewing machine stopped working). It is time consuming but can be done in one day if you work on it a lot. I made mine in two days. Crank up the Christmas tunes!

Here’s how I did it: 

Materials:

  • round vinyl/flannel back table cloth
  • 5 colors of lightweight fabric (dark to light in color). I purchased 2 yards of the darkest, 2 yards of the second darkest, 1.5 years of the next color, 1 yard of the lightest colors. Yes, a lot. I bought 7.5 yards of fabric. {Use coupons! Look for sales/clearance fabric.}
  • Hot glue (approx. 100 glue sticks) OR swap out hot glue for sewing
  • Duct tape

Tools: scissors, iron

Tutorial:

1. My round table cloth was was too large. I started by folding it in half and placing it under the tree. This gave me an idea of where I’d want to cut. I didn’t measure. Just decided I needed to cut off about 10-12 inches. no sew tree skirt2. I folded the half circle table cloth in half again to create a pie-slice shape. Then just cut {rounding it} approx. 10″ from the outer edge. how to make a no sew tree skirt 3. Snip the pointed edge of the folded table cloth. no sew ruffled tree skirt 4. Cut along one fold from outer circle to inner. no sew tree skirt tutorial5. Place under the tree and decide if more needs to be trimmed. And if I liked the “Twister” vibe of my vinyl table cloth, I’d be done! But, um. No. Something better in mind.

no sew tree skirt

Tip: cover edges of smaller hole {where tree trunk will be}  with duct tape. I used FrogTape. This little area is susceptible to tearing…tape will help prevent tears.

6. Spread out fabric {keep folded}. Any size strips will do. Larger widths will create bigger ruffles. Smaller widths, smaller/more ruffles. I decided on small 4 1/2 inch wide strips. I marked the fabric and cut my strips (no need to be a perfectionist about perfectly straight strips but keep as straight as possible). Length doesn’t matter. Most of my fabric was 54″ wide, but one of my fabrics had a smaller width.

no sew ruffled tree skirt

A lot of strips! 7. Time to iron. And iron. And iron some more.

no sew tree skirt tutorial

Take a break.

8. Start at the outer edge, along the vertical cut (the back of the tree skirt). Folded edge towards you, raw edge will be glued. Place the strip of fabric so it hangs off the vinyl table cloth.  I applied hot glue to the end of a strip of fabric, attach to back side on flannel and wrap around to the front of the vinyl (only about an inch or so on the back). no sew ruffle tree skirt9. I worked in about 4-6inch sections (just eye-balling it, making sure to hide the outer edge of the vinyl table cloth. I applied a line of hot glue, then pressed the raw edge of the folded fabric strip onto the hot glue line. AS I WENT, I’d create “pinch” pleats (glue a straight 2-3 inches, fold the fabric up towards you, then press down another 2-3 inches of fabric strait onto the hot glue line.

no sew ruffled ombre tree skirt tutorial

10. Insert a small amount of hot glue into the folded fabric. Press down flat.

no sew ruffled ombre tree skirt tutorial

11. Attach the little flaps with a dab of hot glue if needed.

no sew ruffled ombre tree skirt tutorial

12. Repeat and continue. no sew ruffled ombre tree skirt tutorial13. When another strip of fabric is needed, open end of fabric, place the end of the last fabric strip, add some glue and fold. (Just create an extended strip of fabric).

no sew ruffled ombre tree skirt tutorial

14. When completing the row around the edge of the circle, cut strip of fabric about an inch and fold onto the flannel back and secure in place with hot glue {as shown in step 8}.

15. Continue onto the next row. Since my ruffles were smaller, I used up all of my darkest color then continued onto the next color. Sometimes it was in the middle of a ruffle, most of the time, I ended a color at the end of a row. My fabric mostly ran four rows. Working towards the center, will require less fabric.

no sew ruffled ombre tree skirt tutorial

16. I noticed that as I worked, my circle wasn’t so perfect anymore. I kept going. Around the trunk area, inner tree skirt, I did have to fill in with fabric strips…again, it’s not perfect…just play with creating more ruffles under what you’ve done, if you see vinyl showing through or have vinyl that’s not circle shaped towards the end. No one will be able to tell…just create pleats/ruffles with the same color to fill in.

17. Near the “trunk” part of the tree skirt, I finished off with a sheer white double ruffle from my scrap supply. You can use wide ribbon…create a double ruffle by hand with a running stitch with thread (no knot) in the center length wise and pulling ends to “gather”. Or use ribbon or bias tape, or follow the same steps but do the last row upside down, gluing raw edge to raw edge, creating pleats/ruffles. Cover hot glued raw edges with thin piece of pretty ribbon using hot glue. no sew ruffled ombre tree skirt tutorial 18. I ran a length of duct tape up the ends of the ruffles on the back side just to keep things neatly tucked down.

ruffled tree skirt

Looks like an expensive professionally sewn beautiful tree skirt, right? So pretty in any color, even drop cloth or burlap or how about using white flat sheets? You’ll have to let me know if you give this a try {or if you already have!}. I’d love to see it!

ombre ruffled tree skirt

Oh – and you will experience some hot glue burns. No sew doesn’t mean no pain. Ouch! But they only hurt for a few seconds.

teal ombre ruffled tree skirt

{Leftover fabric strips were torn into thinner strips and used as garland.} Stop back later this week for Christmas tree pictures!

Don’t miss a post and see sneak peeks first by following along:

DIY Show Off DIY Holiday Highlights

Partying here:

Home Stories A2Z

Holiday Craft Party at Centsational Girl